Tag Archives: tip of the week

How to Install a Hardwood Floor

DIY experts take us step-by-step to help install beautiful wood floors

Step 1: Choose the Boards

Choose the hardwood species and board widths for the room installation.

Step 2: Measure the Room

Measure the width and length of the room and multiply for the square footage. When ordering hardwood flooring, allow 10-15 percent extra for irregular boards and any cutting mistake.

Step 3: Check for a Squeaky Floor

Check the sub-floor. Minimum requirements are a 3/4″ plywood sub-floor. Make sure there are no squeaks in the floor. If there’s a squeak, screw a long drywall screw into the sub-floor and joist where the squeak occurs. Remove shoe-molding from the room and sweep and clean thoroughly.

Step 4: Roll Out the Vapor Barrier Paper

Roll out strips of vapor barrier paper, allowing at least a 4″ overlap and staple securely to the sub-floor. Use 15 pound tar paper or felt. It is relatively inexpensive (it’s approximately $12 a roll at a home improvement store). Mark with a pencil along the baseboards where the joists are located.

Step 5: Start Installation

Start the installation at the longest unobstructed wall. Remove the shoe molding, and snap a chalk line 3/8″ out from the baseboard (this allows for expansion in the hot, humid weather and contraction in the colder, drier weather of the hardwood flooring).

Step 6: Place the Boards

Begin by selecting a long board to start the first row. Pick one that is straight. Align the edge of the board with the chalk line and drill pilot holes down through the hardwood plank and into the sub-floor and joist. Face-nail each board at the point of every joist and set the nail with a nail-set. Face-nail the entire first row and remember to keep the board lengths random. It is important to face-nail the first row because the pneumatic nail can’t get down in there. It will hit the wall and the force would push the wood against the baseboard, which would lose the 3/8″ expansion and contraction.

It is important to lay the first boards perpendicular to the joists which are underneath. That is important because you want a nice solid anchor. Look at the subfloor to see which way the nails and seams ran. Try to go underneath the crawl space to see how they run.

Step 7: Hand-Nail the Rolls

After the first few rows have been installed, drill pilot holes down into the tongue of each board and hand-nail the rolls until there is enough clearance for the pneumatic nail gun.

Tip: Lay out a box of hardwood boards ahead of the installation to visualize lengths, wood grain and colors of the boards. When laying out the boards, keep in mind to never have the ends of boards in adjacent rows line up with each other. Keep the lengths random and at least 6″ in length.

Step 8: Staple the Boards

Using the pneumatic nail gun, place the gun lip over the edge of the board and strike firmly with the mallet, driving the staple into the tongue of the hardwood plank.

When installing up to a threshold, it is not critical to make cuts exact. Come back later after the floor has been installed and use a circular saw to cut across for a precise cut.

use pneumatic nail gun to staple tongue into plank

Step 9: Cutting the Baseboard

When cutting along the baseboards, select a piece that will fit in there and leave 10 or 12 inches more and cut it off. Use the other piece on the beginning of the next row. You don’t always have to get it in there real close and throw out the end piece. That will save some time and waste.

use cut off boards from one row to start next row

Step 10: Fill in the Gaps

Be sensitive to the way the ends fit together. One end has a tongue and the other end has a groove — this is called end matched. Make sure to always cut the wall end of the wood so that you do not cut off the groove that fits to the tongue. If that happens, that would result in a pretty big gap. Find a piece and lay it alongside the hole and flip it over. Make sure when you make the mark to cut off the wall side, not the room side. When you make the mark, butt it up against the baseboard and then mark at the end of that tongue. That will leave a 3/8″ gap for expansion and contraction when installing the piece.

Note: Before nailing, make sure to put at least two nails in every board. The rule of thumb is to place a nail every 10″ to 12″.

Step 11: Work Around Clearance Issue

As you near the opposite wall, clearance for the pneumatic nail gun again becomes an issue. Drill pilot holes and hand-nail the boards until there is no longer clearance for the drill and hammer. At that point, drill pilot holes down into the top of the boards and face-nail the boards, remembering to set the nails with a nail-set.

Tip: Use a pry bar and a few extra scraps of flooring to firmly seat the hardwood plank as you nail.

Step 12: Fit Last Board Into Place

If there’s a narrow gap for the last board, take a measurement and rip (cut length-wise) the last board to fit into place. Remember to leave a 3/8″ gap at the end wall for expansion and contraction space.

Step 13: Fill Holes With Wood Putty

Replace shoe molding in the room and putty all of the nail holes that have been face-nailed. Be sure to get wood putty that matches the floor. Fill the hole and wipe off the excess.

Step 14: Hardwood Floor Maintenance

Maintenance is easy for a pre-finished hardwood floor — keep grit off of the surface by sweeping regularly and use a flooring cleaning kit (alcohol-based) and spray on and wipe off with a damp cloth. Hardwood floors also help cut down on dust mites.

See more pictures and examples at http://bit.ly/129zwQu

How Your Floors Reflect Your Style

What better way to start a fresh year than to re-design a room to match your wood floors?  The correct flooring and texture go hand in hand with the interior design of your home. It has much to do with the layout, feel of your home, and the style that you wish to have. Wood flooring has become a very popular, modern trend that many have become fond of as an addition to their homes.

Design sets a sense of style that catches an eye when entering a room.  In order to choose your perfect hardwood flooring, design is the first step that factors into your transformation. It is ultimately the most important decision when it comes to choosing the correct flooring.

In fact, your own inspiration is what sets the decision making process.  Start with a plan.  How would your room look in order for you to be content with it when you walk in? Ask yourself a few more questions. What objects in your home inspire your lifestyle? Do you enjoy a modern look? A contemporary one? Or are you more traditional when it comes to the comfort of your home? Of course, there are many more factors that go into the decisions of creating your newly designed room.  Considerations include the size of the room, color of the walls, and the idea that the colors must complement each other for the final product to be beautiful. It is important to remember the color of your floors should not match perfectly with your walls or furniture. Diversity is key, but it should also be done tastefully. The color of your wood floor can be light, natural, or a darker stain. It is all up to your own preference.

Sofa-and-wooden-floor-in-living-room“In terms of a traditional look, dark wood floors suggest a formal appearance. Lighter colored walls as well as floral accessories accent the room greatly”.

Luanne Kelchner

Quotes from experts can be inspiring as well.  Holly is a design expert who has a love for art, design, and architecture.

“The wood flooring in a home is a critical part of the perfect design. It should be a canvas or a place to start for the overall picture that a quality designer will create. It should not be the focal point but a back drop.”

Remember, plenty of design magazines and books have even more visual tips to help create your perfect home.  When your interior style changes, there are many things you can do to re-arrange the look of your home.  Furniture and accessories say it all when a change of heart occurs!

 

Plugin from the creators of Brindes Personalizados :: More at Plulz Wordpress Plugins